electric motor on my compressor turns slow an trips the breaker was working fine the last time I used it.

by gary
(Ponca City, OK.)

33 gal. 11.9cfm. craftmans. A.O.smith motor. 115V rpm3450 mod. 919.167340. motor turns slow then trips breaker work fine last time it was used. how many ohms should this motor show on meter. ITs showing 3


____________________________
Bill says...

I don't have the spec for that, Gary.

If you go to www.searspartsdirect.com and input your model number, you can see the parts diagram and parts list.

You can also (if during business hours) chat on line with them. I would ask if that info was in the manual before I ordered one, or, just if they knew what that was.

What is the pressure in the tank when "motor turns slow then trips breaker"? On cut in with pressure, or even when the tank is empty?

If no change in the power supply to the compressor, then check the intake filter to make sure it's clean, pull the line from the pump head to the tank and see if the compressor runs OK then. If so, apply gloved back pressure to the fitting or port in the pump head to see if this causes the motor to lug. If not, pull and clean the check valve, then try it again.

Cheers,

Bill

Comments for electric motor on my compressor turns slow an trips the breaker was working fine the last time I used it.

Click here to add your own comments

Apr 09, 2015
Start capacitor
by: Anonymous

I also have an older Craftsman compressor with the same symptoms. I figured it was the capacitor. I ordered start and run capacitors. I received the start capacitor today, installed it , and no improvement. I now have confidence that when I receive the run capacitor, it will work.

Feb 19, 2014
919.167340 Craftsman Air Compressor Fix
by: Ben

I have this same compressor and it was tripping the breaker just like yours. I would plug it in and turn the power lever to the "on" position and it would slowly start to run and after a few seconds the breaker would trip. I got mine working again by replacing the "Run Capacitor". This compressor has two capacitors. Run Capacitor and Start Capacitor. Contact me direct and I can walk you thru the steps I took to getting it fixed and running again. Capacitors are cheap $10-$25. They do hold power charge so don't touch the contacts with your bare hands. I have pictures and step by step instructions.

Ben
Truckman2k@aol.com
________________
Ben, thanks for this. If you would like me to add a page to this site with your instructions and photos, please contact me using the contact page with the link you get from my system included so I can locate the original post.

Bill


Bill

Click here to add your own comments

Add your own question or comment. It's easy to do. How? Simply click here to return to Electrical-troubleshooting-compressors.

220v 2.2kw capacitor start, capacitor run motor, runs slow and overheats

by Frank Duffin
(Cardiff, Wales, UK)


Got this motor to run a hydraulic press. Even when not connected to press the following happens:
Motor starts up really slow, the cable (16 amp) starts to heat up from the plug end. If left on for more than a minute the motor starts to heat up.

It is a 220v motor single phase.

Was working before being posted to me, it was taken to 2500psi where it stalled the pump.

I am certain the supplier is correct and it was ok before posting.

The plug is connected to a 30amp main fuse in my house. It blew a 13amp fuse before I changed the fuse to 20amp. I am wondering if the problem is the start capacitor/run capacitor or the changeover switch?

I am just using a normal switch, ie no soft start, DOL etc. My research suggests that this motor should run on a normal 220v household supply, albeit linked to a 16amp + fuse.

Frank
The connection box has four connections, U1, U2, 3 and 4. My live is connected to U1, neutral to U2.

Click here to post comments

Add your own question or comment. It's easy to do. How? Simply click here to return to Electrical-troubleshooting-compressors.

Just replaced brushes and put it back together - Running Problems

I have a CFBN 125A-3 I just replaced brushes and put it back together and it stutter runs.

I mean it runs and turns off over and over as though someone is plugging it in and out. Can You Help?

_________________________
Bill says...

Friend, it seems clear to me that if the problem didn't exist before your re & re the motor, and now the problem is there, it is something you did or didn't do on the rebuild.

I hope someone that rebuilds electric motors reads this and can offer so guidance.

Cheers,

Bill

Click here to post comments

Add your own question or comment. It's easy to do. How? Simply click here to return to Electrical-troubleshooting-compressors.

Air compressor motor stops

by Terance W. Cooley, Sr.
(Ankeny, Iowa USA)

after I push the reset (red) button, the compressor will run for about 5 seconds and then cut off. The air tank is not full at all of air.

______________
Bill says...

Sounds like motor is failing, or you haven't enough current to the motor to allow it to run properly.

The reset button is often a thermal reset. The cut off occurs when the motor gets to hot, to try and save it from heat related damage. By repeatedly pushing the thermal reset, and not addressing the issue that caused it, you are likely doing more damage to the motor.

Make sure nothing else is pulling power from the same circuit that feeds your compressor. If, after that, the symptom continues, I'm guessing that your motor is the problem.

Cheers,

Bill

Click here to post comments

Add your own question or comment. It's easy to do. How? Simply click here to return to Electrical-troubleshooting-compressors.