As I look at the features of the Central Pneumatic model 67501, I can't help comparing it to one of the air compressors in my workshop. Mine is a dead ringer for the 67501 if you simply remove the Harbor Freight / Central Pneumatic decals and replace them with another brand name. I suspect the same factory in an Asian country supplies this model of air compressor to big box stores all over the world.
With a 2 HP motor and an 8 gallon tank, the model 67501 provides enough air for short-burst air tools, but no where near enough to try to run grinders, sanders, air-blasting equipment. I use my similar model for blowing off the workbench, table saw and planer, driving some brad-nailers, and airing up tires of course.
The 67501 air compressor is useful anywhere that the 125 PSI that is available from this Central Pneumatic air compressor, in a relatively low flow, can do the job.
In late 2013 this model is still available to be purchased from Harbor Freight. This means that parts and some support should be available from them.
There appears to be enough interest in the Central Pneumatic 67501 air compressor to have a forum on this model, to help folks looking for information and a place for present users to offer assistance to others with the same air compressor. This is the forum page.
After reviewing the existing postings and the troubleshooting pages to see if your question is already answered, if your 67501 issue has not been addressed, please use the form below to post your own question about the 67501 air compressor from Central Pneumatic (Harbor Freight).
If you own a 67501 and see a question you can help with, please add a comment to that post. I appreciate it.
As the numbers of comments added to this page grows, it may get harder for you to find the post with the specific answer you are seeking. I've added a search box here for your use to help you find the information you need.
Having an issue to ask about or share regarding your Central Pneumatic Model 67501 Air Compressor?
Please see below. You may find the solution to your compressor problem has already posted.
I just bought a used model 67501
I didn't notice the the threaded plug was broke. It appears to be the plug to add oil. First I would like to know where I could get a manual for …
Central Pneumatic 67501 blowing oil
My compressor is blowing oil out of vent in oil fill cap.
My 67501 compressor won't start..
Turn on/off switch to on,just clicks,compressor won't start and run.
Starts up in cold (30F or below), builds pressure and motor won't turn over again..
I start my compressor in cold weather. The compressor runs well until a build up of the pressure. After the build up it shuts down. I try restarting …
Pressure switch failing
67501 2HP 8Gal. The Reset Button/ Automatic Shut Off Switch is shot. How do I go about purchasing a new switch? I hope someone has a recommendation. …
Central Pnuematic 67501 = Hard start in cold weather
Hello: In cold of chilly weather, I have a hard time getting my air compressor to start. I turn on the switch and it will run for a second or two, them …
67501 - starts but won't run
central pneumatic model 67501 . i just put a new capacitor on it . it did not help . first it run for appox 10 seconds then quit . tried the reset …
Central Pneumatic 67501 will not restart under pressure?
CP Model No. 67501; 2 HP will not restart under pressure The compressor builds to 125+/- PSI as it should, but when out flow falls to about 60 PSI, …
Rod broke - need parts
the rod connection the piston broke and i can't find a replacement. Any idea where I can get parts?
Where to purchase Central Pneumatic pressure guage
Pressure guage was accidentally broken. Cannot fine replacement part with 250 psi. Can I use a guage that only goes to 160 psi? I never use it for over …
central pneumatic model 67501 reset button keeps kicking off
won't build preasure reset button keeps kicking off like the motor gets hot reset button kicks off comppressor like new _______________ If the compressor …
Central Pneumatic model 67501 8 gallon compressor
I was working with a nailer and the compressor started but then acted as if the starter valve malfunctioned, its happened before, called HF and obtained …
67501 will not start when cold?
I HAVE A MODEL 67501 COMPRESSOR WHEN I GET READY TO START IN MORNING IT TRIPS THE RESET SWITCH THIS IS MY SECOND COMPRESSOR IN 5 MONTHS THAT HAS DONE THIS. …
Rebuild kit for Central Pneumatic 67501 air compressor?
Is one available? Where can I get one? Approximate cost? Considering purchasing this model from Harbor Freight and also want to be sure it is not the …